• 4 Ways Remote Control Switch (Works 20 To 50 MTS) ON/OFF One Lamps/Fan
• 4 Ways Digital Telecontrol Switch, Wireless Remote Control Switch, Remote Controller
• Remote Control, Replace Original Wall Switch Directly, Radio Frequency, Anti-Interference, No Barrier
• Suitable For Home, Office, Hotel, Factory, Hospital, Restaurants, Meeting Rooms, Museum, Shop, and Art Gallery etc

It is a 5V 8 Channel Relay Module. The relay normally open interface maximum load: AC 250V/10A, DC 30V/10A. It has a trigger current of 5mA, and module working voltage of DC 5V. Each channel of the module can be triggered by a jumper to set a high level or a low level. Fault-tolerant design, even if the control line is disconnected, the relay will not move. With status indicator: power (green), 6-channel relay status indicator (red).All module size interfaces can be directly connected through the terminal block, which is convenient and practical.

Features :

1. Power supply and relay instructions, lit, the disconnect is off;
2. The input signal, signal, common Terminal and start conducting;
3. Useful for appliance control;
4. DC or AC signal, control, you can control the 220V AC load.
5. One normally closed contact and one normally open contact
6. Triode drive, increasing relay coil
7. High impedance controller pin
8. Pull-down circuit for the avoidance of malfunction
9. Power supply indicator and Control indicator lamp
10. The module is compliant with international safety standards, control and load areas isolation trenches.

Specification :

• Operating Voltage (VDC) : 3 ~ 5
• Trigger Voltage (VDC) : 5
• Switching Voltage (VAC) : 250@10A
• Switching Voltage (VDC) : 30@10A
• Storage condition () : 65 to 125
• Operating Temperature (C) : -40 to 85

Features:

• MD optocoupler isolation, driving ability, stable performance; trigger current 5mA.
• Each channel module can be set high or low level triggered by the jumper.
• Power indicator (green), 4 Relay status indicator (red)
• When com with low short circuit, triggering the corresponding relay is low, and high when com shorted
• Channel: Channel 4
• Operating Voltage: DC 5V
• Max Load: 250VAC 10A/ 30VDC 10A

Each channel has an LED light indicating the operating status of the relay. This is a relay power supply with terminal blocks and a DC power outlet two kinds of interface forms, the use of more flexible and more convenient. With a diode freewheeling protection circuit. With the use of a dual power supply, the user can according to need, through the short-circuit cap, select the power supply to use more flexibly and conveniently.

• Board around with four fixed screw holes, hole diameter 3.1mm, easy to install and fixed
• Relay selection of high-quality loose relay, single-pole double-throw. A common end, a normally open end, a normally closed end
• Optocoupler isolation, good anti-interference
• Low level pull-in, high-level release. Pull the status indicator light, release the status indicator is off
• VCC for the system power, JD_VCC for the relay power. Plug in the jumper cap

Specifications-

Specification:

• 1 channel relay board
• Operating Voltage 5V
• Max Current: 20mA
• Relay Contact Current Capacity at AC250V: 10A
• Relay Contact Current Capacity at DC5V: 10A

This is the 5V relay most commonly used as switching device in electronic circuits. It is mainly used in Commonly switching circuits, For Home Automation projects to switch AC loads, To Control (On/Off) Heavy loads at a pre-determined time/condition, Used in safety circuits to disconnect the load from supply in event of failure.

• Nominal Coil Voltage: DC 5V
• Structure: Sealed type
• Coil Sensitivity: 0.36W
• Coil Resistance: 70-80 ohm
• Contact Pin Length: about 3.5mm    

Package Included:

1 x 5V  10A PCB Mount Relay – Sugar cube 5 pin

This is the 12V relay most commonly used switching device in electronics. It is commonly used in Home Automation projects to switch AC loads, To Control (On/Off) Heavy loads at a pre-determined time/condition, Used in safety circuits to disconnect the load from supply in event of failure.

Specifications:

• Contact rating: 7A 250V AC
• Coil voltage: 12V DC
• Coil current: 30mA
• Coil resistance: 400Ω
• Coil power: 360mW
• Operate time: 10ms
• Release time: 5ms
• Insulation resistance: 100MΩ min.
• Dielectric strength: 1500V
• Operating temperature: -40°C to +70°C

   Package Included:

1 x 12V 10A PCB Mount Relay